Honda HR-V Owners & Service Manuals

Honda HR-V: Symptom Troubleshooting

ALL THE DOORS AND THE TAILGATE WILL NOT LOCK AND UNLOCK

Refer to: Keyless Access System Symptom Troubleshooting - All the doors and the tailgate will not lock and unlock

AUTO DOOR UNLOCK DOES NOT WORK

Refer to: Keyless/Power Door Locks/Security System Symptom Troubleshooting - AUTO DOOR UNLOCK does not work

CANNOT SELECT ON MODE WITH KEYLESS ACCESS AND WITH THE KEYLESS REMOTE TOUCHING THE ENGINE START/STOP SWITCH

Refer to: Keyless Access System Symptom Troubleshooting - Cannot select ON mode with keyless access and with the keyless remote touching the engine start/stop switch

CANNOT SELECT ON MODE WITH KEYLESS ACCESS, BUT CAN SELECT ON MODE WITH THE KEYLESS REMOTE TOUCHING THE ENGINE START/STOP SWITCH

Refer to: Keyless Access System Symptom Troubleshooting - Cannot select ON mode with keyless access, but can select ON mode with the keyless remote touching the engine start/stop switch

DOORS AUTOMATICALLY RELOCK 30 SECONDS AFTER BEING UNLOCKED WITH THE KEYLESS REMOTE EVEN THOUGH A DOOR HAS BEEN OPENED

Refer to: Keyless/Power Door Locks/Security System Symptom Troubleshooting - Doors automatically relock 30 seconds after being unlocked with the keyless remote even though a door has been opened

IMMOBILIZER SYSTEM SYMPTOM TROUBLESHOOTING - ENGINE DOES NOT START WITH THE IMMOBILIZER KEY

NOTE: Before troubleshooting, check the items listed in General Check before Troubleshooting.

1. Problem verification.

  1. Try to start the engine.

Does the engine start?

YES

Intermittent failure, the vehicle is OK at this time.

NO

Go to step 2.

2. Immobilizer system check.

  1. Turn the vehicle to the OFF (LOCK) mode.
  2. Turn the vehicle to the ON mode, and check the immobilizer indicator.

Does the indicator blink once, then stay off?

YES

Go to step 3.

NO

Go to the immobilizer indicator blinks troubleshooting - Refer to: Immobilizer System Symptom Troubleshooting - Engine does not start with the immobilizer key, or Immobilizer System Symptom Troubleshooting - Immobilizer indicator does not go off, or Immobilizer System Symptom Troubleshooting - Immobilizer indicator blinks.

3. Starting system check.

  1. Turn the vehicle to the START mode.

Does the starter motor run?

YES

Go to step 4.

NO

Go to starting system, and check the starter motor.

4. PGM-FI system check 1.

  1. Try to start the engine with the immobilizer key.

Does the engine start?

YES

Go to step 5.

NO

Go to the PGM-FI system symptom troubleshooting.

5. PGM-FI system check 2.

  1. Wait for a few minutes with the engine running.

Does the engine stop?

YES

Go to the PGM-FI system symptom troubleshooting.

NO

The system is OK at this time.

READ NEXT:

 Immobilizer System Symptom Troubleshooting - Immobilizer Indicator Blinks

NOTE: Before troubleshooting, check the items listed in General Check before Troubleshooting. 1. Immobilizer system check. Connect the HDS to the data link connector (DLC). Turn the vehicle to the

 Immobilizer System Symptom Troubleshooting - Immobilizer Indicator Does Not Go OFF

1. Immobilizer system check. Connect the HDS to the data link connector (DLC). Turn the vehicle to the ON mode. From the SYSTEM SELECTION MENU, enter IMMOBI, then select IMMOBILIZER INFO. NOTE:

 Keyless Access System Symptom Troubleshooting - All The Doors And The Tailgate Will Not Lock And Unlock

1. Door lock actuator operation check 1: Remove all the keyless remotes from inside the vehicle, and close all doors and the tailgate. Push each LOCK and UNLOCK buttons of the keyless remote, at

SEE MORE:

 Audio Remote Switch Test

Test SRS components are located in this area. Review the SRS component locations - Refer to: SRS Component Location Index (KA/KC), or SRS Component Location Index (KA/KC) and the precautions and procedures before doing repairs or service. 1. Driver's Airbag - Remove 2. Lower Garnish Assembly - Remo

 Engine Oil Filter Feed Pipe Removal and Installation

Removal 1. Oil Filter - Remove 2. Oil Filter Feed Pipe - Remove Installation 1. Oil Filter Feed Pipe - Install Install the two 20 x 1.5 mm nuts (A) onto the oil filter feed pipe. Hold one nut with a wrench, then tighten the other nut Apply new engine oil to the oil filter feed pipe threads.

© 2019-2025 Copyright www.hohrv2.com