Honda HR-V Owners & Service Manuals

Honda HR-V: Inclination Sensor Initial Learn Procedure (CVT)

Procedure

NOTE:

  • The inclination sensor initial learn procedure must be done with the HDS when:
    • The PCM is replaced.
    • The inclination sensor is removed/installed, or replaced.
    • The inclination sensor malfunction occurs.
  • There are two procedures depending on a work area:
    • On a level ground; the learning procedure is performed once.
    • On a slope; the learning procedure must be performed twice.
  • Do the procedure twice when a work area is not verified the level.
  • If the inclination sensor initial learn procedure is not carried out, the R indicator in the gauge control module will come on or blink.
  • Do the procedure with a one-man, in a vibration free environment, and do not develop the vibration during the procedure.
  • If any DTCs were indicated with the HDS, go to the indicated DTC's troubleshooting first.
  • The learning of the inclination sensor initial settings overwrites the existing driving information data of the inclination sensor system in the PCM.

1. Inclination Sensor - Initial Learn Procedure

On a Level Ground

  1. Apply the parking brake.
  2. Check the tire pressures, refer to the tire information label on the driver's doorjamb. Adjust the pressures to the specified value if necessary.
  3. Connect the HDS to the DLC.

    NOTE: For specific operations, refer to the user's manual that came with the Honda Diagnostic System (HDS). Make sure the HDS is loaded with the latest software.

  4. Select the Inclination Sensor Learn in the Miscellaneous Test Menu, then select the Inclination Sensor Initial Learn Procedure and learning procedure once with the HDS.
  5. Follow the HDS screen, and learn the initial settings. The inclination sensor initial learn procedure is completed when the HDS indicates the TEST COMPLETE.

    NOTE: If the HDS does not indicate the TEST COMPLETE, follow the HDS screen and learn again.

On a Slope

  1. Apply the parking brake.
  2. Check the tire pressures, refer to the tire information label on the driver's doorjamb. Adjust the pressures to the specified value if necessary.
  3. Make the aligning marks on all tires and ground.
  4. Connect the HDS to the DLC.

    NOTE: For specific operations, refer to the user's manual that came with the Honda Diagnostic System (HDS). Make sure the HDS is loaded with the latest software.

  5. Select the Inclination Sensor Learn in the Miscellaneous Test Menu, then select the Inclination Sensor Initial Learn Procedure and learning procedure twice with the HDS.
  6. Follow the HDS screen, and do the first learning procedure.
  7. Turn the vehicle around to do the second procedure from the front to the rear. Park the vehicle with aligning the marks on the tires with the marks on the ground, and apply the parking brake.
  8. Follow the HDS screen, and do the second procedure. The inclination sensor initial learn procedure is completed when the HDS indicates the TEST COMPLETE.

    NOTE: If the HDS does not indicate the TEST COMPLETE, follow the HDS screen and learn again.

PCM RESET (CVT)

Procedure

1. HDS - Connect

2. PCM - Reset

  1. Select the A/T SYSTEM with the HDS
  2. Reset the PCM with the HDS while the engine is stopped
  3. Turn the vehicle to the OFF (LOCK) mode
  4. Turn the vehicle to the ON mode, then wait for 30 seconds
  5. Turn the vehicle to the OFF (LOCK) mode, then disconnect the HDS from the DLC.

Fuel and Emissions Systems Learning Procedure

3. Fuel and Emissions Systems - Learn

CVT Control System Learning Procedure

4. Inclination Sensor - Initial Learn

    READ NEXT:

     Shift Lock Solenoid Test (CVT)

    Test 1. HDS - Connect 2. Shift Lock Solenoid - Test Select the Shift Lock Solenoid Test in the Miscellaneous Test Menu, and check that the shift lock solenoid operates with the HDS. Check that t

     Transmission Fluid Temperature Sensor Test (CVT)

    Test 1. Vehicle - Lift 2. Engine Undercover - Remove (With 2WD) 3. Transmission Fluid Temperature Sensor - Test Disconnect the connector (A).NOTE: To prevent damage, cover the connector using a s

     Check

    TRANSMISSION FLUID (HCF-2) LEVEL CHECK (CVT) Check NOTE: Keep all foreign particles out of the transmission. Check the transmission fluid level after the shift lever operation without spending to

    SEE MORE:

     Lane Departure Warning System Description - Overview

    The lane departure warning system determines if the vehicle is unintentionally leaving the lane in which it is travelling. By identifying the lane markings in reference to the vehicle position, the system issues an audible warning and visual warning in the multi-information display when vehicle la

     DTC B0028-12

    Special Tools Required SRS Inflator Simulator 07SAZ-TB4011A SRS Simulator Lead L 070AZ-SNAA300 NOTE: Before doing this troubleshooting procedure, find out if the vehicle was in a collision. If so, verify that all the required components were replaced with new components of the correct par

    © 2019-2025 Copyright www.hohrv2.com