Honda HR-V Owners & Service Manuals

Honda HR-V: DTC 1102 USB Diag

Honda HR-V (2015-2021) Service Manual / Accessories & Equipment / Audio-Navigation System - Diagnostics / DTC 1102 USB Diag

NOTE:

  • Check the vehicle 12 volt battery condition first.
  • This navigation DTC sets when a problem is detected with the USB device that is connected to the USB port.
  • Before you troubleshoot, make sure to follow the General Troubleshooting Information.
  • Check any official Honda service website for more service information about the navigation system.

1. Problem verification:

  1.  Clear the hard error codes.
  2.  Turn the vehicle to the OFF (LOCK) mode then the ON mode.
  3.  Connect the USB device to the USB adapter A or the USB adapter B.
  4.  Check for hard error codes.

Is DTC 1102 indicated?

YES

The failure is duplicated, go to step 2.

NO

Intermittent failure, the system is OK at this time.

2. Audio-navigation unit check:

  1.  Clear the hard error codes.
  2.  Turn the vehicle to the OFF (LOCK) mode.
  3.  Disconnect the USB device, then connect a known-good USB device to the USB adapter A or the USB adapter B.
  4. Check for hard error codes.

Is DTC 1102 indicated?

YES

Replace the audio-navigation unit.

NO

Original USB device is faulty.

DTC 1102 USB DIAG

NOTE:

  • Check the vehicle 12 volt battery condition first.
  • This audio DTC sets when a problem is detected with the USB device that is connected to the USB port.
  • Before you troubleshoot, make sure to follow the General Troubleshooting Information.

1. Problem verification:

  1. Clear the hard error codes.
  2. Turn the vehicle to the OFF (LOCK) mode then the ON mode.
  3. Connect the USB device to the USB port A or USB port B.
  4. Check for hard error codes.

Is DTC 1102 indicated?

YES

The failure is duplicated, go to step 2.

NO

Intermittent failure, the system is OK at this time.

2. Audio unit check:

  1. Clear the hard error codes.
  2. Turn the vehicle to the OFF (LOCK) mode.
  3. Disconnect the USB device, then connect a known-good USB device to the USB port A or USB port B.
  4. Check for hard error codes.

Is DTC 1102 indicated?

YES

Replace the audio unit - Refer to: Audio Unit Removal and Installation (Display Audio Type (7-inch Screen), or Audio Unit Removal and Installation (Color Audio Type (5-inch Screen).

NO

Original USB device is faulty.

    READ NEXT:

     DTC 1301 GPS Antenna Error

    NOTE: Check the vehicle 12 volt battery condition first. This audio DTC sets when there is poor connectors or loose terminals at the GPS antenna connector or an open in GPS antenna lead. Before

     DTC 1302 GPS Receiver Error 1

    NOTE: Check the vehicle 12 volt battery condition first. This audio DTC sets when there is an internal GPS receiver problem (freeze error). Before you troubleshoot, make sure to follow the Gener

     DTC 1303 GPS Receiver Error 2

    NOTE: Check the vehicle 12 volt battery condition first. This navigation DTC sets when there is an internal GPS receiver problem (reboot error). Aftermarket metallic window tint or electronic de

    SEE MORE:

     Cylinder Head Assembly - Inspection & Adjustment

    INSPECTION & ADJUSTMENT CYLINDER HEAD INSPECTION FOR WARPAGE Inspection 1. Cylinder Head - Remove 2. Cylinder Head Warpage - Inspect Check the cylinder head for warpage. Measure along the edges, and three ways across the center: If warpage is less than 0.08 mm (0.0031 in) cylinder head

     Clock

    Adjusting the Clock Models without navigation system You can adjust the time in the clock display with the ignition switch is in ON (II)*1. ■Adjusting the Time ■ Display audio system 1. Select the (HOME) icon, then select Settings. 2. Select System, Clock, then Clock Adjustment. 3. Adjust t

    © 2019-2025 Copyright www.hohrv2.com